Method 1: Timed automatic operation mode (recommended)

1. Power on

As shown in Figure 2, press 1 (the main power switch) on the controller to the "I" position, then the power of the whole set of equipment is turned on.

The LCD screen will light up and display the company introduction and simple instructions at the same time, and the green power indicator on the printer will light up.

2. Fully automatic timing operation

After the device is turned on, referring to Figure 1, first press the 3 (manual speed-down key) key, then 1 (LCD screen) displays the time setting screen, each time you press

Once the 2 (manual speed-up key) key, the time display increases by 5 minutes, and then returns to 0 after 40, restarts. When the time limit is set

After time, press the 4 (Run / Stop) key, the device enters the timed automatic operation process, when it is effective

Effective state) After the time reaches the set time, it will automatically enter the post-vibration scanning, and then stop. The entire scanning and aging process, the equipment will follow the best process

automatic completion.

After the equipment finishes running automatically and stops, press 5 (print key) to print out the a-n and a-t curves and data for long-term storage.

Operating attention

1. There is a peak point in the scanning process;

2. The acceleration at the peak point should exceed 60 m / s2;

3. When the acceleration value of the peak point exceeds 160 m / s2, the device will automatically protect.

Method 2: Fully automatic operation mode:

1. Power on

As shown in Figure 2, press 1 (the main power switch) on the controller to the "I" position, then the power of the whole set of equipment is turned on.

The LCD screen will light up and display the company introduction and simple instructions at the same time, and the green power indicator on the printer will light up.

2. Fully automatic operation

Press the 4 (Run / Stop) button directly, the vibration aging equipment will automatically enter the fully automatic operation process.

After the equipment finishes running automatically and stops, press 5 (print key) to print out the a-n and a-t curves and data for long-term storage.

Operating attention

1. There is a peak point in the scanning process;

2. The acceleration at the peak point should exceed 60 m / s2;

3. When the acceleration value of the peak point exceeds 160 m / s2, the device will automatically protect;

4. Time is not controlled.

Method 3: Semi-automatic operation mode:

Boot

As shown in Figure 2, press 1 (the main power switch) on the controller to the "I" position, then the power of the whole set of equipment is turned on.

The LCD screen will light up and display the company introduction and simple instructions at the same time, and the green power indicator on the printer will light up.

Refer to Figure 1 and "Four-⑵-C", "Four-⑵-D" and "Four-CD-C" in the operation configuration instructions, through 2 (manual speed-up key

) Key and 3 (manual speed-down key) key to set the speed and time to be effective and press the 4 (Run / Stop) key, the device will automatically enter

Enter semi-automatic operation mode.

After the equipment is automatically stopped after operation, press 5 (print key) to print the a-t curve and data for long-term storage.

Method 4: Manual operation mode:

1. Power on

As shown in Figure 2, press 1 (the main power switch) on the controller to the "I" position, then the power of the whole set of equipment is turned on.

The LCD screen will light up and display the company introduction and simple instructions at the same time, and the green power indicator on the printer will light up.

2. Manual operation

Press the 2 (manual speed-up key) key. Press once to increase speed slowly, press twice to increase speed. Usually press twice. After pressing the 2 (manual speed-up key) key,

There is a current display. After a period of time, there will be a speed display. When there is speed display, the motor keeps increasing speed. Press 3 at this time (manual speed reduction

Key), the motor stops at the speed to run at a speed. Press 2 (manual speed-up key) again and the motor will run again to continue speed-up. Until the workpiece starts to vibrate

, You can press the 3 (manual speed-down key) key to stop at the speed for aging treatment. After a certain time, press the 4 (Run / Stop) key to complete the aging process.

Operation Note: In addition to the manual aging of the workpiece, the manual operation mode is generally used for the processing of new workpieces or workpieces with special shapes to check

Check whether the support of the workpiece, the position of the exciter, the position of the sensor and the size of the excitation force are appropriate; the manual mode can be used to control the excitation at will

The speed-up and speed-down function of the device can quickly find the resonance frequency of the workpiece and the size of the resonance point.